Market Price : USD675.00
My Price : USD395.00
Complete HHO Systems for your cars and trucks!
Installation Manual on CD with picture and diagram included!!
Easy installation with bracket included!
"Stainless Steel Tubes type Dry Cell circulate water between Generator to Water tank faster than Plates Dry Cell type.
Just imagine the tubes produce hydrogen that are lighter and blow it on top of the s.steel tubes into the water tank.
While at the bottom of the tubes, it suck water from the water tank to flow through the s.steel tubes and generate hydrogen.
This gives the better HHO production and cooler the generator.
Its a simple method hydrogen and oxygen will automatically float to the top and push the water together into the water tank
This is why Stanley Mayer use tube type generators"
The System uses spare electricity from your cars alternator to generate Hydrogen gas from water.The Hydrogen is fed into the manifold of your vehicle...The results are astounding, more torque at lower engine speeds, lower emissions, cooler engine, less carbon build up and considerably more miles per gallon.
The System is manufactured in the Malaysia, incorporates all the latest safety features and is designed to last a lifetime ... The System was designed, developed and tested by an experienced team of researchers... The system has been fitted locally as a complete system for over 18 months and thoroughly tested by dozens of happy customers using water for fuel.
Stanley Mayer stainless steel hollow pipe generator design that i found to produce more HHO and cooler than the plate type. it suck water from the bottom and blow on top of it.
Support 12v/24v current up to 30amp. and the production of HHO can be speed up to 1.5l per min.
Suitable for engine 2000cc-4000cc.
All tubes connectors are push pull type. easy to connect or disconnect.
Easy to install with diagram included.
The Kit Contains The Following:
- 1- Hydrogen Generator stanley mayer type hollow with stainless steel pipe
- 1 - Stainless Steel canister
- 1 - 3 in one HHO controller (PWM + Dual EFIE + AMP Meter) with 12v 2 ball bearing fan.
- 1 - Water tank as bubbler
- 1 - 40 amp Relay
- 1 - Fuse and fuse holder.
- 1 - Lubricant oil tank with twin valve controller.
- 1 - Air intake valve with T connector to your cars manifold intake
- 1- 5 ft. Vacuum Flex Tube for easy push/pull fittings
- 2- Steel bracket and clips.
- 1- Manual For Installing The Hydrogen Generator (CD)
 |  |
| This Stanley Mayer tubing design will circulate electrolyte for maximum HHO production and cooler electrolysis process. | Syntactic base motor oil tank to lubricate the piston in a dry and lean combustion. Make you engine run smoother and prevent the piston from burning if the fuel is too lean. (This item it self can safe 5-10% of your fuel usage) |
 |  |
| Aluminum and Stainless Steel Material | Water tank as bubbler. Rotating water flow between the canister and bubbler. |
 |  |
| A complete package. Includes tubing and wiring. | Easy to refill and see through water level. |
 |  |
| Stanley Mayer design that help to regulate water from the generator to the water tank. | Bracket for easy and strong installation of the generator and water tank. |
 |  |
| Valve vacuum controller that will prevent your engine to suck too many oxygen into your intake manifold. | Valve speed control to your intake manifold. |
 |  |
| 3 in 1 HHO controller.30 amp Pulse width modulator + 30 amp ampere meter + Dual EFIE or MAF/MAP controller. Control the volume of HHO production. (10-25% saving) | Lubrication tank with twin control valve.Use 500ml of lubrication for every 20 liters of fuel. |
 |  |
| Longer lasting with high grade stainless steel. | Complete systems for your cars. |
 |  |
| Ready to ship worldwide.
| Inside the HHO Controller with 12v 2 ball bearing fan. 30 amp PWM and a dual EFIE controller. |
 |  |
| D.I.Y guide to install in less than 1 hour. | Photo of location of the generator and bracket |
 |  |
| 304 Grade stainless steel build to last | Stainless Steel canister. Keep out of glass and PVC type of canister. |
1. Pulse Width Modulator
WE HAVE DESIGNED THIS BOARD SPECIFICALLY FOR HHO GENERATION.
THIS PWM WILL LET YOUR GENERATOR TO WORK ON A LOWER TEMPERATURE BUT THE SAME PRODUCTION.
FOR ONE THING, NO MORE DRIVING AROUND WITH A RED HOT PWM UNDER YOUR SEAT OR DASH BOARD WITH THIS (12v) 2 BALL BEARINGS FAN THAT IS 5 TIMES MORE POWER THAN NORMAL COMPUTER FAN (5V).
PUT ANY AMOUNT OF ELECTROLYTE AND THE PWM WILL LET YOU CHANGE THE AMPERE AT ANY AMP BETWEEN 0-30AMP.
Power Supply: 12 or 24 Volts DC
Load Voltage: 12/24VDC 30 AMPS
Output Frequency: 400 Hz
Output Power is Adjustable from 0% to 100%, or anything in between. (control perfect amount of HHO Production )
PCB Dimensions: 3.85 x 1.59
2. MAF/MAP Sensor or EFIE
This Map Sensor Enhancer is needed for vehicles made after 1995. EFIE is for cars with computer setting.
Without this increased mileage cannot be achieved by the addition of Hydrogen Enhancement alone, and the mileage may actually decrease.
This sensors will tweak your cars computer to lean more fuel. With EFIE installed, you can control the RPM of your engine. This item it self can save you 10-25% fuel usage. But it cannot be use without HHO generators.
Made with quality parts that meet exact Water4Gas specifications, including 10-50k linear potentiometers and 33k resistors.
Swtich between MAF/MAP or EFIE.
EFIE setting will send more volts(2.3v more) to your computer, higher voltage will lean more fuel. or switch to MAF/MAP for normal operation that will adjust the vacuum of your intake manifold either to richer or leaner fuel.
All connections are precision soldered to ensure a lifetime of performance.
The dials turn 270 degrees for fine tuning.
All electrical connectors are supplied with instructions and wires are labeled.
3. Lubrication Oil System
In many case, we found that when a car system is tweak to lean more fuels, it will increase the engine temperature. This is because HHO will burn 100% of fuel in the combustion chambers. When the fuel is too lean, there's no fuel left that can your engine need for lubrication. This is not good for your piston and engine will burn easily. So we design this lubrication oil system to moisturize the piston and keep the movement smooth and lower the temperature of the engine. This system is also use in Natural Gas Vehichle (NGV).
The lubrication oil to use is a synthetic base 2 stroke motor oil you can get easily in local store or pump station.
4. The HHO Generator
20 to 30% better mileage can be expected depending on your vehicle and your ability to tweak the system out. In some cases I have seen over a 50 to 70% increase. Maximum saving can be achieve when you are driving on a highway with constant speed (70-90mph)
This cell works very well with 20 tablespoon of baking soda applied only the first time it is being used. This new design generator can support up to 30amp of 12v/24v current.
The best production is between 15-20amp.
HHO PRODUCTION PER LITER
1. 12v 10amp - 0.3-0.5l p.m.
2. 12v 20amp - 0.8-1.5l p.m.
3. 12v 30amp - 1.5-2.0l p.m.
Tested production on a vacuum condition. The HHO production result may very depends on the generator water temperature and electrolyte use.
When the water gets low you only have to fill up with distilled water from there out. The baking soda you initially put in the system will stay there until you completely clean it out. I recommend before you attempt to install or operate any of these units to read and fully understand this system. With care and regular maintenance this unit will last for years!
The whole kit will come with directions on how to install this yourself! It is very simple to do and can be installed in about an hour! Install the hydrogen generator, wiring and hook up one line to a vacuum line and the other line to your air intake. install the HHO Controller where you can see from drivers seat. just make sure the amp is between 15amp to 20amp.
5. 30amp Ampere Meter
AC/DC 30Amp ANALOG PANEL METER, to help you regulate the amperage and control production as well as regulate temperature in the cell.
connection diagram between amp meter wire, relay and generator included.
What others says about our product :
Im really interested in distributing your product In my local area with installation and service done in my shop. Love the design. I agree that it should be more efficient than the plate or dual rod designs. - gigylow
I am amazed at the overall quality of your product. It is clearly the most professional hydrogen generator in the Ebay market. I believe you could make steady sales in the United States for $400/single generator - EASY!! That is, if your product is sold IN the united states. Let me be your guy in the United States to make a transition to American markets. Once again, you have a tremendous product and I look forward to complimenting the appeal it has. Please let me know how you feel. - steve4611
Interested in offering them at my garage... will save me assembly time. - bestbuyniaga
okay here's the deal... stan meyers design has intrigued me for years... the cost of materials in the US is ridiculous... we may have a good thing here.. thanks! - vinnystapleton
We have been looking at this technology for a while now, and were just starting onto development of this as well. We would perhaps be interested in licensing this technology or perhaps taking care of the manufacture of this for you for the North American market. - samoy2002
Your systems look well made. My mechanic and I will purchase some system in the near future. You seem knowledgeable...you should have information as to how you started making these. It would give you credibility since you are out of the U.S. You'll sell a lot more units if you can provide information for people like me who have basic information, but are confused as to which system to buy. We may even buy one. - rubytheparrot
Postage:
5-10 Days Worldwide Delivery Charges : USD37.90
Ship to Malaysia USD20.00
Ship to Singapore,Brunei Indonesia & Thailand USD20.00
This product is full of Stainless Steel & Brass material so it will be a bit heavy (3.0kg)
Its an autopart not a kitchen ware.
Package size : 18inch X 4 inch X 8inch.
We will only send parts damage* during delivery. Please take photos and send to my email Subject : REPLACE PART GENERATOR (EBAY ITEM ID).
*damage means : without replacement the item wont work as usual.
We re not responsible for any lost or stolen parts during shipment.
We will only ship to ebay/paypal address! Please make sure you update your address including contact number.
READY STOCK!!!
The system design and photo shown here is for the current design. The item you may receive may be different and may change depends on current updates without notice.
